ASTM A564 PDF

Best Stainless offers high quality standards including UNS S, AMS , ASTM A, and ASTM A Grade PH stainless steel can be used. This standard is issued under the fixed designation A /A M; the number . [ mm] round bar, 10 to 12 ft [ to m] in length, ASTM A See the chemical composition and physical properties of ASTM A Grade condition HM, find alternative materials, and connect with suppliers.

Author: Nale Fauzahn
Country: Lesotho
Language: English (Spanish)
Genre: Science
Published (Last): 24 February 2008
Pages: 82
PDF File Size: 10.29 Mb
ePub File Size: 15.32 Mb
ISBN: 605-6-19435-447-2
Downloads: 99450
Price: Free* [*Free Regsitration Required]
Uploader: Dousar

Users of this standard are expressly advised that determination of the validity of any such patent rights, and the risk of infringement of such rights, are entirely their own responsibility.

The values stated in each system are not exact equivalents; therefore, each system must be used independent of the other. Type and stainless steels contain a large amount of ferrite in the microstructure and can have low ductility in forgings and large diameter bars.

If you feel that your comments have not received a fair hearing you should make your views known to the ASTM Awtm on Standards, at the address shown below.

Billets or bars for reforging may be purchased to this specication. Hot-finished or cold-finished rounds, squares, hexagons, bar shapes, angles, tees, and channels are included; these shapes may be produced by hot rolling, extruding, or forging.

  GE CARESCAPE V100 PDF

ASTM A 564

Your comments are invited either for revision of this standard or for additional standards and should be addressed to ASTM International Headquarters. Hot-finished or cold-finished rounds, squares, hexagons, bar shapes, angles, tees, and channels are included; these shapes may be produced by hot rolling, extruding, or forging.

Shapes may be subjected to either Class A or Class C preparation for removal of visible surface imperfections. A superscript epsilon indicates an editorial change since the last revision or reapproval. Astmm Documents purchase separately A546 documents listed below are referenced within the subject standard but are not provided as part of the standard.

Type UNS S shall be furnished in solution annealed, cold-worked or aged-hardened condition. Historical Version s – view previous versions of standard.

Combining values from the two systems may result in nonconformance with the specification. On sizes 12 in. When specied, the material, as represented by impact test specimens, shall be capable of developing the impact property requirements specied in Table 4 when heat treated in accordance with 5.

D BH for rounds cold drawn after solution treating. Originally approved in Number of Tests 8. This specification covers bars and shapes of age-hardening stainless steels. The limiting permanent offset shall be 0.

ASTM A A M R_百度文库

Type UNS S is suitable for machining in the solution-annealed, cold-worked, and aged-hardened condition. Applications should be limited to small diameter bar.

They are suitable for machining in the solution-annealed condition after which they may be age-hardened to the mechanical properties specied in Section 7 without danger of cracking or distortion.

  LG 32LC52 PDF

Up to 6 in. Up to 4 in. C Unless otherwise noted, temperatures shown are suggested temperatures and may be varied to obtain required tensile properties. Warm in air to room temperature. Combining values from the two systems may result in nonconformance a54 the specification. Limits are in percent maximum unless shown as a range or stated otherwise.

The values stated in each system are not exact equivalents; therefore, each asgm must be used independent of the other. Link to Active This link will always route to the current Active version of the standard. The values stated in each system are not exact equivalents; therefore, each system must be used independent of the other. Note 2 — For billets and bars for forging see Specification A Material of types other than XM, XM, and Type asrm be furnished in the astj condition, or in the equalized and oven-tempered condition.

G Columbium 8 times carbon minimum.

17-4 PH Stainless Steel Bar

Type XM is machinable awtm the as-received fully heat treated condition. D Intermediate temperatures must meet the ductility requirements of the next highest suggested hardening or aging temperature, or both. Active view current version of standard. CW 12 hard CW full hard 7.