ILS-CON. ILS™ Control Center. USER MANUAL. Page 2. ILS-CON User Manual. 2 Legend™ R. DMX-. to create a profile for this fixture the Chauvet Legend DMR-ILS, PDF manual can be downloaded and I can create the profile for you. Chauvet | DMX Omega I | Instruction manual | Chauvet DMX Omega I Legend R Legend RX Legend 8bit Legend 16bit Legend .
|Published (Last):||28 June 2014|
|PDF File Size:||2.67 Mb|
|ePub File Size:||6.27 Mb|
|Price:||Free* [*Free Regsitration Required]|
If you make a mistake in Edit Fixtures, or simply wish to revert to the original values from the fixture library legsnd press the [Reset All] key.
References to front panel controls, buttons and lights appear in capital letters, for example: This includes cues, chases and effects. A select key allows you to select the playback for programming or manipulation on the Master Playbacks. These four options are mutually exclusive, with the default option being [Track Forward] as shown above. Connect your media to the USB port on the desk any port will do.
To prevent this confusion, it is recommended to first edit the fixture number using chauvwt Edit Fixtures screen before commencing patching using this method.
In this function, any values defined for Pan will be output on the Tilt channel sand any values defined for Tilt will be output on the Pan channel s. Tracking — This option defines the behaviour of the desk when recording cues. Subsequent cues can then be set up and recorded in a similar way.
Help to Create a Profile | ADJ Forums
The next cue in the cue stack is automatically loaded when the fader reaches zero. This is indicated by these twenty faders turning green. Pressing each of the soft buttons on the touch screen cycles round the three options for that attribute, except when they are forced to red see below. Page 71 Desk Setup — this allows you to configure behaviour, default times and other hardware settings.
Set Time – Press the [Set Time] key on the monitor. Fade times are stored as soon as they are modified, so there is no need to update or re-record submasters to store these changes. Chauveg long as the console IP address and the PDA IP address are able to see each other, the system should automatically setup and configure. Setup is intended to give you access to the core settings for the ORB. Chakvet touch screens can be connected to the desk via VGA and USB ports as an option to provide you with easier input facilities.
With the MFFs in the correct mode, channels can be adjusted by moving the appropriate fader. A common method of recording an effect is to apply one of the standard effects, adjust the affect parameters as required using the wheels or Effect Window and then record this as a new effect palette.
Like Fade view, the fixture chauvte can be used to adjust the timing of a parameter. The value of the middle selected fixture will be locked. It is important here to ensure that the DMX universe is correctly selected.
Submasters Submasters are scenes stored onto faders. Press the [Renumber] soft key.
To copy the outputting manaul of a cue, do the following: Each of the cue stacks has a soft button in the window. The Update Options window will appear. The Manul Fixture popup window is displayed on the monitor screen with the current patch address in the DMX Address field Select the required Universe by clicking on the [Universe] button and selecting the universe from the drop down menu. Each view has the dropdown box at the bottom to select a new view.
Select the [OK] button. The Load Show Window is Select the required show from the list of available shows displayed. Pressing the TRY CUE key again plays back the new look back over the corresponding times default or recorded times depending on what data was in the programmer. If you want us to add support for a different screen, then we may ask you to loan us the screen including the drivers CD that came with it for a short time for testing.
Once active, the system allows bidirectional control of fixtures, selection and patching via the Ethernet connection. To continue running the cue stack, press the GO key. These options are only applicable and accessible when a cue or cues are selected. The fader controls the HTP levels; the LTP channels are triggered when the fader is moved from the end stop and then fade according to the times in the incoming cue.
Naming Palettes Palettes can be named, either as a separate operation or as part of the recording process, by entering one of the following commands: First select the fixture s required as described above and then use the intensity wheel to adjust the level.
A drop down menu is displayed on the touch screen. There is no UNDO function so exercise caution when using this function. Soundskilz Inc in Murri Behaviour — Keep parameters separate options; Confirm Overwrites.
Fade Time Commands — Editing Cues The following commands can be used to globally edit the fade times of parameters in existing cues: The monitors are used extensively to display information and shortcut buttons. Set up the fixture outputs as required, ensuring that the correct parameters are tagged.
For example, a palette can be stored for the colour Red which details the DMX values required for each moving light to create a Red colour.
Help to Create a Profile | ADJ Forums
If you have used the Patch Wizard then you will have chauvwt altered these numbers as part of the process. Graphical Interface The desk operates a graphical interface which is provided by up to two external monitors. Each DMX universe can also be output over Ethernet, using various communication methods.
Each console is assigned an IP address and a master or backup status. When the [Desk Information] key is selected a screen is displayed containing information on the various software, pegend and BIOS installed in the desk as follows: You can change this selection as required before saving the data to the palette.