VideoBloX Configuration Program (VideoCFG). All VideoBloX matrix switchers are supplied with the VideoBloX Configuration Program. This is the software tool . Honeywell’s VideoBloX matrix system is a robust video and audio full The VideoBloX embedded CPU is a 1⁄2U size module programmed using Windows-. Honeywell’s Data Port Expander provides additional RS ports for the connection of keyboards and Protocol Interface VideoBloX NetCPU System.
|Published (Last):||4 November 2014|
|PDF File Size:||7.73 Mb|
|ePub File Size:||11.68 Mb|
|Price:||Free* [*Free Regsitration Required]|
History Issue Date Revisions Document Location of Phillips Screw and Pulling Tool Users of the product videolox responsible for checking and complying with all federal, state, ad local laws and statutes concerning the monitoring and recording of video and audio signals. Honeywell video systems shall not be held responsible for the use of this product in violation of current laws and statutes.
NetCPU | VideoBloX | Analogue Products | Honeywell Commercial Security UK
Users of the product honeyqell responsible for checking and complying with all federal, state and local laws and statutes concerning the monitoring and recording of video and audio signals. Honeywell Video Systems shall not be held responsible for the use of this product in violation of current laws and statutes.
Quick stops, excessive force, and uneven surfaces may cause the product and cart combination to overturn. Compliances and Safeguards To reduce the risk of fire or electric shock, do not expose this product to rain or moisture. Do not insert any metallic object through the ventilation grills.
This unit must be properly grounded videoboox a good earth ground. Each system must contain at least one VideoBloX chassis. It is possible to interconnect more than one chassis either at the same location or at different locations with suitable data and video interlinks between the various racks. The modules are fitted horizontally to allow for vertical system expansion.
All modules except the power supply module are position independent.
Two thumb screws for removing modules from the chassis are provided with each chassis. Allowing for insertion of the power supply module accessible from the front of the VideoBloX chassis. Perform the following procedure to remove a module from the VideoBloX chassis. If removing the power supply module, remove power to the unit. Power indications are visible The UPS is not provided by Honeywell and videoblod the responsibility of the installer. The pin-out of this connector is automatically modified depending on the configuration of the chassis being a master or slave.
The rear chassis Control and Comm connectors are RS connections. Connect the Control Connector on the second chassis first slave chassis to the Comms connector on the third chassis second slave chassis. All other chassis must be set honeywelll as slaves. Should the chassis be configured as a master, then all slave chassis will also receive a reset signal.
Each of the inputs may be routed to 1 or more of the 64 backplane channels. All input modules have 16 video inputs, but can be switched to 16, 32, or 64 maximum outputs. Older modules have front panel termination cideoblox and some have internal termination jumpers. When connected using coaxial ribbon cables, each chassis receives all 16 video inputs.
The ‘B’ style cross-connection module allows for interconnection of up to 4 VideoBloX chassis. Note that the address is set in binary. For more information, please refer to Appendix A. Each time that a videobkox message is received via the backplane and is addressed to the module, the LED will flash off briefly.
Honeywell VideoBloX User Manual
The input module has one PCB mounted fuse, rated at 4A. This fuse should only honyewell in the event of a fault on the board. In such an event the input module should be returned to Honeywell for repair. Honeywekl of noneywell outputs is associated with one of the 64 backplane channels. The output module has a range of jumpers which are populated to determine which group of 16 video outputs the module receives from the backplane. Leave it in the Off position honeywe,l 10 seconds.
This clears the non-volatile memory of the Titled Output module. This level will result in a bright LED indication for “Signal”, with only occasional flashes of honeeywell “Peak” LED when the input signal is at the maximum expected level.
Set the phantom power jumpers on the audio input module as described in paragraph User configurable jumpers allow this module to be available in two options, channel 1 to 32 and channel 33 to Should a matrix be expanded to more than 64 outputs, these two options are still used and refer to the backplane channels within each subrack. No part of this publication may be reproduced by any means without written permission from Honeywell Video Systems.
The information in this publication is believed to be accurate in all respects. However, Honeywell Video Systems cannot assume responsibility for any consequences resulting from the use thereof. Page of 74 Go. Table of Contents Add to my manuals Add.
Page 7 VideoBloX Chassis Page 8 Tables Rev 1.
VideoBloX NetCPU Matrix Switching System
Compliances And Safeguards Users of the product are responsible for checking and complying with all federal, state, ad local laws and statutes concerning the monitoring and recording of video and audio signals. European Compliance Statement Users of the product are responsible for checking and complying with all federal, state and local laws and statutes concerning the monitoring and recording of video and audio signals.
Page 14 Compliances and Safeguards Rev videobllx. Features Each system must contain at least one VideoBloX chassis.
Dip Switch Settings Page 74 Document Comments to this Manuals Your Name. Enter text from picture: By pressing ‘print’ button you will print only current page. To print the manual completely, please, download it. Don’t show me this message again. Got it, continue to print.
Don’t have an account?