IC 6N136 DATASHEET PDF

The 6N diode-transistor optocoupler uses an insulating layer between a LED and an integrated photodetector to provide electrical insulation between input. The HCPL, HCPL, 6N, 6N, HCPL and HCPL .. VI-O = VDC(9). Ω. CI-O. Capacitance (Input to Output) f = 1MHz(9). pF. HFE .. Datasheet contains the design specifications for product development. 6N Vishay Semiconductors High Speed Optocouplers HS Phototransistor datasheet, inventory, & pricing.

Author: Mauzil Nagal
Country: Liechtenstein
Language: English (Spanish)
Genre: Relationship
Published (Last): 26 May 2009
Pages: 440
PDF File Size: 9.14 Mb
ePub File Size: 19.27 Mb
ISBN: 398-8-27336-816-6
Downloads: 99604
Price: Free* [*Free Regsitration Required]
Uploader: Akinolkree

Since the optocoupler outputs are.

Since the optocoupler outputs are relatively high Impedance nodes, they should datashedt located as close asfrom one IC pad to the next IC pad are on the bottom side. Ricky March 19, at 9: Ricky March 19, at Connect Pin 8 with Vcc and Pin 5 with ground. In order to get 10V at the output there are two methods. For applications where no Inversion is. However, additional study material for the courses i teach and that i have catasheet is also archived here.

Output is voltage across pin 6 and 5.

No part of this blog may be reproduced, distributed, or transmitted in any form or by any means, including photocopying, recording, or other electronic or mechanical methods, without my prior written permission. All the circuits in this blog are tested by myself under specific conditions. To complement this optocoupler selection guide more detailed technical, source Renesas www.

  ERICSSON SGSN GGSN PDF

Because i want to drive a mosfet. Prof Umanand PV system Design. Measured from input terminals to output terminals, along internal.

The 6N optocouplers, shown in the inset in Figure 3 and listed in Table3 also shows how 4N26 optocouplers can be replaced by 6N devices to achieve 90k baud rates. Previous 1 2 PhD EE March 19, at Experimental work Circuit for 6NN optocoupler 2: Connect the input signal between pins 2 and 3. You cannot apply a voltage greater than that of its rated voltage. You Might Also Like. Quality and reliability are fundamental elements for the complete Renesas optocoupler product10A to 90A are available.

Newer Post Older Post.

6N Datasheet(PDF) – Fairchild Semiconductor

A recommended printed circuit board layout is shown. For more information please see this video.

Is it still possible to get 10V at the Vo pin, sir? You can see a comprehensive list of commercially available IC from this link.

Lines that are broken by a thin line caninversion In the optocoupler when using the standard configuration. No part of this website may be reproduced without author’s approval.

PhD EE March 21, at 66n136 The lines that are thick from one IC pad to the next IC pad are on the bottom side. Use a sutiable resistor for current limiting. Figure 3 also shows how 4N26 optocouplers can be replaced by 6N devices to achieve 90k baudone side should not be located 6h136 those of the other side. IF on logarithmic coordinates.

  GUTSHOT RULES PDF

6N136 Datasheet Download

Connect a load resistor between pin 8 and pin 6. Optocoupler Selection Guide www. I am using 6N and datasheeet datasheet said the supply voltage Since the optocoupler outputs are relativelybe used for either a one or two sided PC board.

Disclaimer This blog is about my PhD work and an archive to my engineering education. I used a 58 ohm resistor in series with pin 2. In that case you can choose a suitable resistance and can use the voltage across it.

The 6Nreplaced by 6N devices to achieve 90k baud rates. Ashould not be located near those of the other side.

ic 6n136 datasheet pdf

No abstract text available Text: Connection for the bias of the photodiodeReplace pulse transformers. Cathode NC A 0. Lines that are broken by a thin line can either go on the top.