IFGC 2012 PDF

The International Fuel Gas Code (IFGC ) is a model code produced by the International Code Council (ICC). This document provides the foundation. SECTION (IFGC) GENERAL. Scope. This chapter shall govern the design, installation, modification and maintenance of piping systems. International Fuel Gas Code IFGC/IFGS CHAPTER 8 REFERENCED STANDARDS ยท APPENDIX A (IFGS) SIZING AND CAPACITIES OF GAS PIPING.

Author: Akiramar Yokora
Country: Trinidad & Tobago
Language: English (Spanish)
Genre: Music
Published (Last): 22 November 2009
Pages: 435
PDF File Size: 10.26 Mb
ePub File Size: 8.65 Mb
ISBN: 218-8-93293-630-7
Downloads: 4266
Price: Free* [*Free Regsitration Required]
Uploader: Grogar

Piping systems shall be of such size and ifhc installed as to provide a supply of gas sufficient to meet the maximum demand and supply gas to each appliance inlet at not less than the minimum supply pressure required by the appliance. Gas Igc Inlet Pressure 3. Most industry professionals are familiar with the I-Codes as the basis of laws and regulations in communities across the U.

Clothes dryer, Type 1 domestic. ICC instructors provide hands-on, practical problem-solving training and are available to teach on-site single or multiday courses. A nonprofit, public benefit corporation, ICC-ES does technical evaluations of building products, components, methods, and materials.

Initial supply jfgc of 8. The I-Codes, including this International Plumbing Code, are used in a variety of ways in both the public and private sectors.

It is founded on broad-based principles that make possible the use of new materials and new plumbing designs. Other approved engineering methods.

Please enter your e-mail address below. The marking shall be spaced at ifhc not exceeding 5 feet mm. Pipe sizing between point of delivery and the house line regulator. Water heater, automatic storage, to gal. The marking shall not be required on pipe located in the same room as the appliance served. We will email you a link to reset your password.

  CAMARA KIRLIAN PDF

2012 International Fuel Gas Code

Where an additional appliance is to be served, the 20012 piping shall be checked to determine if it has adequate capacity for all appliance s served. Capacity at 2 gal. The total connected hourly load shall be used as the basis for pipe sizing, assuming that all appliances could be operating at full capacity simultaneously.

Capacity at 6 gal. This chapter shall govern the design, installation, modification and maintenance of piping systems. Piping, tubing and fittings shall either be tested by an approved third-party testing agency or certified by an approved third-party certification agency.

Each length of pipe and tubing and each pipe fitting, utilized in a fuel gas system, shall bear the identification of the manufacturer.

Less than 2 psi.

Table of Contents | International Fuel Gas Code | ICC premiumACCESS

Piping from multiple meter installations shall be marked with an approved permanent identification by the installer so that the piping system supplied by each meter is readily identifiable. However, the impact of the codes extends well beyond the regulatory arena, as they are used in a variety of nonregulatory settings.

This code is founded on principles intended to establish provisions consistent with the scope of a plumbing code that adequately protects public health, safety and welfare; provisions that do not unnecessarily increase construction costs; provisions that do not restrict the use ifcg new materials, products or methods of construction; and provisions that do not give preferential treatment to particular types or classes of materials, products or methods of construction.

  IBM SYSTEM STORAGE DS3524 PDF

Table capacities are based on Type K copper tubing inside diameter shownwhich has the smallest inside diameter of the copper tubing products. Certification of building and construction-related products. Where Equations and are used to size piping or tubing, the pipe or tubing shall have smooth inside walls and the pipe length shall be determined in accordance with Section This edition presents the code as originally issued, with changes reflected in the through editions and with further changes approved by the ICC Code Development Process through When adopting a model code like the IFGC, some jurisdictions amend the code in the process to 22012 local practices and laws.

Initial supply pressure of Built-in top unit, domestic. All pipe utilized for the installation, extension and alteration of any piping system shall be sized to supply the full number of outlets for the intended purpose and shall be sized in accordance with Section Gas Natural Inlet Pressure 2. There are several that relate specifically to the IFGC. The applicability of this code to piping systems extends from the point of delivery to the connections with irgc appliance s and includes the design, materials, components, fabrication, 202, installation, testing, inspection, operation and maintenance of such piping systems.

Code Development Current Version: Sign In or Register Ifg. Space and Water Heating Units.

Reference works related to building design and construction.